arm64: dts: qcom: shikra: Add LT9611UXD HDMI bridge and overlay support - #1813
Merged
Shiraz Hashim (shashim-quic) merged 4 commits intoSep 11, 2026
Conversation
…ors and pinctrl Rename lt9611-specific regulator and pinctrl labels to more generic names since these are shared with other DSI panel interfaces. - vreg_lt9611_vcc -> vreg_disp_3p3 - vreg_lt9611_vdd removed (vdd now sourced from pm8150_s4) - hdmi_reg_en -> lcd_bias_en - lt9611_irq_pin -> bridge_irq_pin - lt9611_rst_pin -> bridge_rst_pin - Add hdmi_connector label to hdmi-connector node Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
Added DSI-HDMI overlays: - shikra-cqm-evk-hdmi: CQM EVK with LT9611UXD HDMI bridge overlay - shikra-cqs-evk-hdmi: CQS EVK with LT9611UXD HDMI bridge overlay Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
Added DSI DLC panel support: - shikra-iqs-evk-dlc-panel: IQS EVK with DLC panel overlay Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
mohitdsor
changed the title
Shikra IQS EVKs can optionally be fitted with an AUO G133HAN01 LVDS panel driven through a TI SN65DSI84 DSI-to-LVDS bridge on i2c3. Add a devicetree overlay that describes the SN65DSI84 bridge and the AUO G133HAN01 panel, and disable HDMI. Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com> Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
mohitdsor
force-pushed
the
shikra_display_overlays
branch
from
September 11, 2026 12:41
2aaac46 to
1421cf2
Compare
Shiraz Hashim (shashim-quic)
approved these changes
Sep 11, 2026
Shiraz Hashim (shashim-quic)
merged commit Sep 11, 2026
708e731
into
qualcomm-linux:tech/all/shikra
4 of 6 checks passed
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
3 participants
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
Add LT9611UXD DSI-to-HDMI bridge support for the Shikra IQS EVK board
and introduce DT overlay infrastructure for HDMI and panel configurations.
The LT9611UXD bridge is connected via I2C bus 4 (address 0x41), powered
by a GPIO-controlled 3.3V regulator (PM8150 GPIO4) and an always-on 1.8V
rail. Reset is on GPIO76 and interrupt on GPIO85. The bridge receives DSI
output from MDSS DSI0 and drives an HDMI-A connector.
Changes:
Add LT9611UXD HDMI bridge node, MDSS display enable, regulators and
pinctrl for Shikra IQS EVK
Rename HDMI bridge regulators and pinctrl to generic names
(vreg_disp_3p3, bridge_irq_pin, bridge_rst_pin)
Add DT overlay files and Makefile entries for shikra-cqm-evk-hdmi,
shikra-cqs-evk-hdmi and shikra-iqs-evk-dlc-panel
Tested-on: Shikra IQS EVK with LT9611UXD HDMI bridge
Signed-off-by: Mohit Dsor mohit.dsor@oss.qualcomm.com
CRs-Fixed: 4673615
Exception Ticket : [QLIJIRA-197] Temporary Downstream Exception request to Enable Display interfaces in DT overlay for…